12864 LCD display screen for 3D printer.
Supports for RAMPS 1.4 control board.
Supports for selecting the files to print.
Compatible with CR-10/CR-10S/S4/S5/Ender 3/Ender 3 Pro 3D Printer.
Premium material made, non-toxic and odorless, easy to use.

Perfect replacement accessory for cr-10/cr-10s/cr-10s pro/sapphire plus 3d printer
Easy and quick to install, strong and durable
Great heat performance, do not worry about printing warping edge problem
Plate is made with high quality aluminum alloy material
24v working voltage, 240w power, save electricity and energy saving

Upgrade aluminum hotbed can be a perfect replacement accessory for D01 3D printer.
Come in size 220 x 220 x 3mm, easy and quick to install, strong and durable.
Heating table and aluminum substrate into one, better temperature stability.
The plate is made with high quality aluminum alloy material, with great heat performance, do not worry about printing warping edge problem.

4PCS MOSFET-Low calorific value, the maximum current can reach 20A.(because the module is limited by area, the current cannot exceed 5A)
Upgraded version of TMC5160 V1.2, the heatsink can completely cover 4pcs MOSFET.
The TMC5160 V1.2 uses a 6-layer board, which is more complete than the TMC5160 V1.1 signal, and the work is more stable and the heat dissipation is better.
Ultra-quiet, avoid losing steps and jittering. Can drive 57 stepper motor.
Only Support SPI working mode, currently only firmware for Marlin 2.0 and above supports the TMC5160 SPI mode.

This extruder set is compatible with Creality Ender 3, Ender 3 Pro and other 3D printers.
Mainly including 2 fans, fan cover, heat block, cooling block, nozzle, throat pipe, connector, cable, tube, etc.
Stainless steel material nozzle throat and high quality resistance whose temperature can up to 260 °C/ 500 °F.
Nozzle and tube connect seamless, prevent material leaking and blocking. Heating tube, 24V 40W.
Durable and good performance, fully assembled, you can install directly, good kit for your 3D printer.

Excellent adhesion, ultrabase covered by microporous coating, shows strong adhesion in printing.
Very easy to take off the models, no tools needed when removing models.
Use clips to fix the glass plate on the hot bed, super flatness, fast and uniform heating.
High temperature higher sticky, the models will stick on bed firmly when temperature is high.
Durable, the special coating is inorganic and has a hardness of 8 Mohs, and it is capable to work at 400℃.

TPU Rubber Based, Natural Semi-transparent Color.
1KG Net (apximately 2.2 lbs) Filament with Clear Spool.
Reinforced Spool with Bigger Inner Diameter to Allow Smoother Pull from Extruder.
1.75mm Filament Diameter (Dimensional Accuracy +/- 0.05mm)
Recommended Extrusion/Nozzle Temperature 210°C - 230°C

As a perfect replacement accessory, the screen fits for Anet N4, CREALITY LD-001, ELEGOO Mars, Anycubic photon 3D printers.
Support 2560 *1440 2K resolution, HD display.
5.5 inch screen size, screen ratio 16:9, high projection pixel and print accuracy.
The screen board is extremely stable, don't need to worry about the inherent problems of touch black screen and other problems.
The screen with high transmittance and long service life.

Made of environmentally friendly PLA, non-toxic and odorless, biodegradable and safe for use
Good tensile strength, good ductility, row neatly and won't knot while using
Stable melting point is more advantageous to ensure the fluent printing process, smooth